|
|
转自SSF
=====================================
Finally we post the revision to the Divine Armor Myth Cloth of Athena, from which we will unveil some of the secrets that still holds one of the most anticipated figures Myth Cloth collection, and you will not see the light until the month December. The prototype we got our hands thanks to SD Distibuciones, does not include the famous shield that must carry the goddess in her left hand, because Bandai Japan unfortunately not included in the shipping time.
The armor has a design formed by several components indivisible parts manufactured in metal and plastic. Pieces we should disassemble to confirm the exact number of pieces that make up this armor. Something that unfortunately we can not do because it is a prototype provided. However, we can say that there are only 11 pieces made ​​of metal. The two pieces that shape the front and back of the bib, the coupling of the wings, the two armlets, one of the two pieces that make up each greave, and the four top pieces of the skirt. A priori metal amount well below the average. Although the case of the new female body is not too surprising, given the precedents of the females released so far. What is perhaps most striking is that the outer part of the shoulder pad is not metal. finish On the subject of armor and bearing in mind that first and foremost this is a prototype, which strikes the eye is that the frame has overall a very soft golden hue largely almost silver. While lower parts like the shoulder pad, the wings or the mask of this object show a very intense golden hue. Also mention that the purple hue that adorns some parts and flanges of the armor is present and stands at all times, perhaps to a lesser extent to the components made ​​of metal, which affords a purple hue different from plastic parts . Considering what is the object and have no figure, we can start with some of the sights of assembly, as is the fact that the base - plate is an entirely bound to Object display. The base has a finish very similar to Stage EX Display, along with a series of indentations disposed on its surface to the correct position of the armor not only, but also of the shield and the banner of the goddess
The base is required because it is directly coupled to the skeleton of the object. Skeleton in the lower half saves around 11 sheets skirt anime version. In anime films, hides the metal part of greaves. The greave is designed in two parts, a metal which is approximately two-thirds of the greave, and one made ​​of plastic, which gives shape to the bottom of this and that in the assembly of the object is placed between the guardabrazo and cuff. Both sides are distinguished by the naked eye. Both interns skeleton cross the greaves and they do the same with the lower fee purple skirt, are introduced directly into the central holes of the baseplate. Meanwhile, the upper half of the torso recreates skeleton figure and she initially placed the two pieces that shape the corset armor. Two pieces of plastic and attach lace serve both the components of the skirt, as the two metal breastplate.
The breastplate is presented as a component divided into three parts, and neck (1) is the only piece that is made of plastic. This piece is held loose at all times on the two other possible without binding. Only in the locking wings, neck lace ago. The rear of the bib (2) is formed by three classical component metal parts together indivisible by two hinges. This component is the one where the hinges attach the pads. Finally the front (3) has internal accommodation POM plastic made ready for the attachment of the ends of the back (2). Say that this arrangement requires the body (skeleton object or torso of the figure) to be consistent and maintain the ends of the back in position.
ll Explain later, but in this object seems it is easy to disengage breastplate corset in the bottom-front. Shoulder pads are attached to the breastplate and present inside the typical linkage of these components in the figures of the Classical Myth Cloth line. It is a component consists of three parts, all plastic and where we find three secondary movements. On the next image, you can see that the shoulder pad on the right side shows the two pieces objetc secondary in the final position allowing the movements of your joints, while the strap of the left side shows the secondary parts in its initial position. Red arrows in the image describes the movements that two secondary parts. The small piece that covers the shoulder only makes a slight turn upward. This continues to be a custom fit by Bandai, as in the original design of the Divine Armor of Athena, this piece remains stowed inside the main pad when the armature is in the form of object. When Goddess wears his armor appears as raised in the final position of this Cloth Myth version. Meanwhile the secondary pad performs two types of movements, a rotational movement, which separates the interior of the main pad, and complementary extension movement which moves down a few millimeters. As the shoulder piece, correct assembly requires a save object secondary pad under the main pad, while in the assembly of figure should remain visible as possible. Also discuss that at least in this prototype, the interior of the pad mechanism only allows extensor movement if we performed previously rotation. On the previous image that shows the movements of the pads, the hole is located in the bottom of the back piece corset a leading edge designs around. This hole in the Object gets covered, more or less as they cover the hole right armband British armor when not wearing the shield on it. Assume that the object of this hole is used as binding an articulated arm for the support, as is already designed to hell.
As usual in all objects of humanoid form, most of the pieces have identical mounting on the figure as the object. Assist in the arm back to a Bandai customization by the arrangement of parts that cover in its object and a further example of some of the nonsense assemblies company. In the original design of the Divine Armor of Athena, the two pieces that protect the Goddess arm maintains its position in the object, while the greaves are attached at the end and are introduced by the guardabrazo. Arm according to the image would be from the bottom up: (1) (3) (2) . As you can see from the picture in detail of the arm, Bandai put the plastic part of the greave (2) between the guardabrazo armband, in the latter part of this object assembly Myth
Cloth is inverted relative to the arm assembly of FIG. therefore the division into two parts of the greba due solely to place the small plastic bottom arm, something for which perhaps would have been easier to create as sometimes special parts for the object. Pieces that could look better and even placed in the correct order, not to mention you could make one piece greba metal. 's helmet this Divine Armor looks simply spectacular, with harmonious forms superbly accomplished and very well defined details. The helmet comes as a component that is divided into three parts: the core helmet, the piece that decorates the front at the height of the forehead and the imposing ridge.
Mounting the skirt is composed of three main parts groups. Of these, undoubtedly the most elaborate and innovative, is the "design bridge" that unites in a single-component, the central motif ornament front and center-rear of the skirt. Both metal parts come together by a curved geometry nerve and POM plastic made. Nerve which adds two fixed hinge joint just before binding to both pieces. In the figure, this piece curved POM plastic is placed in the crotch of Athena. The two pins that are free in the front and back of this curved ridge, understand that they are for the attachment of the pieces that shape Athena dress skirt. In the pictures you can see in detail its design and its position in the whole object. For installation, the joints where they are before the pieces of armor, is housed in the lower laces that have the two pieces that make up the corset. At the rear, the sheet is embedded in the metal piece is the only component of this set detachable, to alternate between long sheet object (in image) and the short blade skirt anime version of this armor. Los two other groups of pieces that shape skirt armor, are the lateral components. Are two sets of symmetrical, each formed by an upper metal-five sheets of plastic. These are coupled to the ball joint POM plastic skeleton, which is inside the metal. As seen in the image, each blade reaches identified by the letter (indicating your position on the left or right of the object or figure) and the number (indicating their order of assembly). Coupling of both sides of the skirt is made ​​directly to the corset. This has been designed two POM plastic parts that are fixed on the sides of the brace when the two halves of this are connected. These two small pieces, each having two forks at different heights. The above serves to attach the side skirt armor, while the bottom serves for the attachment of the Athena dress skirt.
To hold the two side skirt and remains closed, is positioned a small spherical pin inside the metal part of each side. Upon closure of the two sides toward the center of the figure, this small pin is engaged in one of the cavities having at its bottom front piece corset. Once assembled around the skirt presents a whole fantastic and very homogeneous. With a near perfect transition curve from the transom to the bottom of the skirt, giving the impression as if it were a single piece. Only in the profile view is seen as the upper component and higher-delatero rear skirt-line stand this. We do not know because this is a prototype and with great trot and passed through several hands, but the coupling of the wings on the breastplate unions detuned quite what the group Dickey-corset-skirt.
The wings have a fantastic design, with very harmonious forms and very in line with what are the wings of Sagittarius Myth Cloth Exclamation version. Precisely Exclamation version of Sagittarius Athena wings inherited the system that allows issuing or replegarlas. Each wing is formed by three groups of pens to be staying within each other when retracted. When the wings are extended are the three groups of feathers while when folded only see two, since the intermediate group which feathers protruding end, remains hidden within the group of feathers that part of the back.
As seen in the image above outstretched wings, the vertical figure looks beaten back by the weight of the wings. This inclination of the body causes the breastplate in his store front inevitably disengage the small flange that holds its position on the corset. And all the blades are disengaged skirt at the bottom purple supplement, being above the front and rear position below. This is all a small review focused on what the armor design Athena and its particularities, we hope you liked it. Remember that the piece that got our hands on a prototype and therefore the final figure is easy to present some modifications or changes.
|
本帖子中包含更多资源
您需要 登录 才可以下载或查看，没有账号？进入圣域
x
评分
-
查看全部评分
|
发表于 2013-11-13 08:59
发表于 2013-11-13 09:07
楼主
金属件好少好少
发表于 2013-11-13 14:49
